首页
›
English Technical Courses
›
033-CAE Automation and LS-DYNA HPC
›
《Oasys PRIMER Model Checking and Batch Automation 100 Cases》
VIP20
本课程属于：033-CAE Automation and LS-DYNA HPC
English Technical Courses · 共 20 门相关课程，组合学习更完整。
查看所属VIP全部课程 →
← 返回所属目录
咨询 / 购买
Oasys PRIMER Model Checking and Batch Automation 100 Cases
100 Lessons
01
PRIMER Model Check Baseline: Open, Inspect, and Export a Clean Model Summary
02
Automate PRIMER Startup and Model Load with a Batch Script Wrapper
03
Scripted Free-Edge Detection and CSV Report Generation
04
Duplicate Node and Element Detection with Automated Merge Proposal
05
Normal Orientation Check for Shell Elements and Flip Report
06
Batch Quality Threshold Sweep for Jacobian and Warpage
07
Automated Penetration Check Between Component Groups
08
Batch Model Check Across Multiple Load Cases Without Geometry Reload
09
Element Quality Dashboard Export to HTML
10
Automated Detection of Unconnected RBE2 and RBE3 Elements
11
Mass and Center of Gravity Consistency Check via PRIMER Script
12
Batch Property and Material Assignment Audit
13
Automated Shell Thickness Range Validation
14
Node Equivalence Tolerance Study with Automated Re-Run
15
Batch Renumbering and ID Range Validation
16
Automated Coordinate System and Local Axis Check
17
Batch Conversion of PRIMER Model Check Results to JSON
18
Automated Free-Body Check for Spot Weld and Connector Elements
19
Batch Model Check Regression Against a Golden Summary
20
Automated Detection of Zero-Area and Degenerate Shell Elements
21
Batch Check of Rigid Body Modes via PRIMER Modal Pre-Check
22
Automated Cross-Reference of Loads and Boundary Conditions to Node Sets
23
Batch Model Check with Component-Based Filtering
24
Automated Element Type Consistency Check Across Components
25
Batch Generation of Model Check Summary Plots
26
Automated Check for Orphan Nodes and Unreferenced Properties
27
Batch Validation of Units and Coordinate Units Consistency
28
Automated Interference Check for Assembly Variants
29
Scripted Model Check for Shell Element Warping Under Deflection
30
Batch Automation of Model Check Log Parsing and Alerting
31
Automated Check of RBE3 Weight Distribution Sum
32
Batch Model Check for Contact Surface Normal Consistency
33
Automated Detection of Overlapping Elements in the Same Component
34
Batch Check of Element Edge Length Distribution
35
Scripted Validation of Node Set Membership Against Geometry
36
Batch Model Check for Beam Orientation and Offset Consistency
37
Automated Generation of a Model Check Exception Register
38
Batch Check of Material Curve and Property Table Completeness
39
Scripted Model Check for Shell Element Aspect Ratio by Component
40
Automated Check of Rigid Element Node Coincidence
41
Batch Model Check with Parameter File-Driven Thresholds
42
Automated Detection of Inverted Shell Elements via Normal Check
43
Batch Validation of Model Check Results Against Solver Deck Syntax
44
Scripted Check for Duplicate Property Names and IDs
45
Automated Model Check Summary Email Generation
46
Batch Check of Node and Element ID Range Compliance
47
Scripted Validation of Coordinate System Definition Completeness
48
Automated Detection of Shell Elements with Zero Thickness
49
Batch Model Check for Free-Edge Closure After Merge
50
Scripted Check of Rigid Element Dependent Node Count
51
Batch Model Check Report Consolidation Across Subassemblies
52
Automated Check of Element Quality After Mesh Morphing
53
Scripted Validation of Load Case Referencing in Batch Mode
54
Batch Check of Contact Pair Penetration Initial Gap
55
Automated Detection of Unmerged Coincident Nodes Across Components
56
Batch Model Check for Shell Element Skewness Distribution
57
Scripted Check of Beam Element Length-to-Depth Ratio
58
Automated Model Check for Orphaned Loads and Constraints
59
Batch Validation of Model Check Output Schema
60
Scripted Check of Element Property Thickness Consistency
61
Automated Detection of Duplicate Load Case Names
62
Batch Model Check for Node Set Coverage of Loaded Regions
63
Automated Check of Rigid Element Orientation Consistency
64
Batch Model Check for Shell Element Taper Ratio
65
Scripted Validation of Material Density and Elastic Modulus Ranges
66
Automated Detection of Elements with Missing Mid-Side Nodes
67
Batch Model Check for Free-Edge Count Stability Across Revisions
68
Scripted Check of Coordinate System Axis Orthogonality
69
Automated Model Check for Element Quality After Property Update
70
Batch Validation of Model Check Results Against Expected Counts
71
Scripted Check of Shell Element Warping Angle Distribution
72
Automated Detection of Unused Node Sets and Groups
73
Batch Model Check for Element Connectivity Across Property Boundaries
74
Automated Check of Load Magnitude and Direction Consistency
75
Batch Model Check for Shell Element Minimum Edge Length
76
Scripted Validation of Rigid Element Weight Factor Sum for RBE3
77
Automated Detection of Duplicate Elements by Connectivity Hash
78
Batch Model Check for Element Quality After Node Merge
79
Scripted Check of Coordinate System Reference Validity
80
Automated Model Check for Shell Element Aspect Ratio Outliers
81
Batch Validation of Model Check Log Completeness
82
Scripted Check of Element Property ID Uniqueness
83
Automated Detection of Nodes Outside Model Bounding Box
84
Batch Model Check for Shell Element Jacobian Distribution
85
Scripted Validation of Load Case Combination References
86
Automated Check of Element Quality After Geometry Cleanup
87
Batch Model Check for Free-Edge Closure After Geometry Repair
88
Scripted Check of Rigid Element Node Set Membership
89
Automated Detection of Elements with Invalid Property Assignments
90
Batch Model Check for Shell Element Warping Under Load
91
Scripted Validation of Model Check Results Against Solver Requirements
92
Automated Check of Element Quality After Mesh Refinement
93
Batch Model Check for Free-Edge Count Reduction After Merge
94
Scripted Check of Coordinate System Axis Length and Scale
95
Automated Detection of Duplicate Load Case Definitions
96
Batch Model Check for Shell Element Thickness Variation
97
Scripted Validation of Rigid Element Weight Factor Sum for RBE2
98
Automated Check of Element Quality After Property Deletion
99
Batch Model Check for Free-Edge Count Increase After Geometry Edit
100
Scripted Check of Coordinate System Origin and Axis Alignment
所属VIP或分类
同VIP：Airbag-Vent-Inflator-and-Deployment
同VIP：Automotive-Crash-Model-Assembly-and
同VIP：CAE-Numerical-Quality-Assurance-and